dimensions in mm (inches). features ? low profile 6.1mm (.240") for minimized mounting space ? characteristic impedance of 50 ohms and 75 ohms ? kinked hold-down allows connector to be fixed on board during soldering kd10 series connectors 2.0mm (.079") contact spacing, board-to-multi coaxial connectors ? ? ? ? ? ? ? ? ? ? ? ? ? ? the kd10 series is a small size multi coaxial connector suitable for middle frequency range. two versions are available: 50 ohms and 75 ohms. the 50 ohms is ideally used for digital information equipment, telecommunication, and calculation equipment, while 75 ohms is used in video movie, radio and multimedia equipment. dimensions and specifications subject to change without notice. general specifications number of contacts 1, 3, 5 and 8 characteristic impedance 50 ohms/75 ohms frequency dc 300 mhz vswr 1.3 max. dc 300 mhz insertion loss 0.3 db/dc 300 mhz current rating 250mamps dielectric withstanding 250 vac r.m.s. (for one minute) voltage insulation resistance 100 megohms min. (with 10mm cable) contact resistance initial (center: 80 megohms max. outer 30 megohms max.) insertion force one pin: 5n max. three pins: 10n max. five pins: 15n max. eight pins: 20n max. withdrawal force one pin: 2n max. three pins: 5n max. five pins: 7n max. eight pins: 11n max. operating temperature -55 c to +85 c insertion/withdrawal 50 times materials and finishes description materials/finishes insulator glass-filled (6-6 nylon) center contact copper alloy, gold over nickel plating outer contact copper alloy, gold over nickel plating hold-down copper alloy, tin plating kd10 C ca ** C 2pl C * *v series cable assembly cable length 60-800mm C every 20 mm longer than 800mm C every 40mm 2 C both ends harnessed none C one end harnessed no. of contacts 1, 3, 5, 8 characteristic impedance d C 50 ohms c C 75 ohms * cable assemblies only available cable plug kd10 C rrp * C f C 0 series termination right angle no. of contacts 1, 3, 5, 8 connector type termination style solder ordering information receptacle connector profile (ref.) 11.5 (.453) 6.1 (.240)
dimensions in mm (inches). pcb hole pattern 1.3 (.051) 0.4 (.016) 2.5 (.098) 0.4 (.016) 5 (.197) 0.4 (.016) 3 (.118) 0.8 (.031) 7.3 (.287) 0.4 (.016) 2 (.079) 0.8 (.031) 9.6 (.378) 0.4 (.016) b 0.4 (.016) a 2 (079) 0.05 (.002) 2.3 (.091) 0.4 (.016) 3.68 (.145) 0.1 (.004) 4.78 (.188) 0.1 (.004) 10.35 (.408) 0.1 (.004) 3.54 (.140) 0.1 (.004) d 0.4 (.016) c 0.4 (.016) note 1: plug side contacts are different for 50 w & 75 w . receptacle side is the same. note 2: applicable cable 50 w : 0.8dCqev 75 w : 8cv-e41447 1 kd10-rrp-f-0 kd10-ca**-*pl-8dv kd10-ca**-*pl-8cv 5.15 ( .203) 6.7 ( .264) 2.8 ( .110) 3.54 ( .139) 2 ( .079) 3 kd10-rrp3-f-0 kd10-ca**-*pl3-8dv kd10-ca**-*pl-8cv 13.15 ( .518) 14.7 ( .579) 10.8 ( .425) 11.54 ( .454) 10 ( .393) 5 kd10-rrp5-f-0 kd10-ca**-*pl5-8dv kd10-ca**-*pl3-8cv 21.15 ( .833) 22.7 ( .894) 18.8 ( .740) 19.54 ( .769) 18 ( .709) 8 kd10-rrp8-f-0 kd10-ca**-*pl8-8dv kd10-ca**-*pl3-8cv 33.15 (1.310) 34.7 (1.367) 30.8 (1.213) 31.54 (1.242) 30 (1.181) plug with cable 50 w 75 w receptacle part number no. of contacts abcde 0.4 0.4 ( .016) ( .016) e 0.1 (.004) a 0.1 (.004) 2 (.079) 0.05 (.002) 2 (079) 0.05 (.002) 2-?.2 (.087) 0.1 (.004) ?.8 (.031) 0.05 (.002) ?.8 (.031) 0.05 (.002) 7.3 (.287) 0.1 (.004) pcb hole pattern (ref.) receptacleCright angle plug (with cable) ** (1): cable assemblies include connector length of 10mm (.039"). if you require 60-800mm (2.36-31.5") cable, you should select cable length every 20mm (.79"). for 840mm (33.1") and above, cable length is every 40mm (1.57"). * (2): blankCharness on one side, 2Charness will be on both sides. kd10 series connectors 2.0mm (.079") contact spacing, board-to-multi coaxial connectors
|
